Nothing spoils the look of a beautiful kitchen like a countertop cluttered with small appliances. Furthermore, nothing is more annoying than dragging the toaster out of a cabinet every morning for a crispy English muffin. Enter the great design debate of form versus function. Should you desire to have your cake and eat it too, (wow we’re really in the kitchen now), then building this DIY-friendly appliance garage is a must. With a cut list that can be sized to fit any space (we provide both our measurements and easy formulas to find your own!), and door slides that push back into the cabinet when not in use, you’re sure to enjoy your perfectly toasted muffin followed by a quick close of the doors to hide it all away.

Note: A door slide is a hinge that opens and then slides the door back along the inside of the cabinet wall. This type of hardware can be a bit pricy ($42 per set on Amazon). If that seems steep, we’ve created the DIY version explained in steps 13-20. Though the door doesn’t slide back quite as smoothly as with the fancy hardware, it’s a viable cost-saving option. Alternatively, you could skip the door slide altogether and opt for regular swinging doors using inexpensive full-inset hinges like this.

 

Cost: $70

Time: 4 ½ hours

Difficulty: Moderate. The layering of thin boards to create the paneled walls and doors is easy, but creating tight joints requires precision cuts.

Tape Measure

Miter Saw

Circular Saw

Pneumatic Nail Gun

Kreg Jig R3

C-clamps

Drill/Driver

1 ¼ inch Kreg Jig Screws

1 inch Kreg Jig Screws

5/8 inch Finish Nails

5/8 inch Wood Screws

1 ¼ inch Finish Nails

(2) ¼-inch Plywood – Get two 2×4 foot project panels to complete the side and door panels and the inside walls and backing board.

(4) 1x2x8 Boards to frame the walls and make the crosspieces and stop block.

(5) ¼x3x4 Boards to trim the walls and doors.

(3) ½x2x4 Boards to frame to doors.

(1) 2×4 Board to support the inside walls.

(2) Cabinet Knobs

(4) Full Overlay Hinges

Wood Glue

Wood Filler

Sandpaper

Primer and Paint

Cabinet Dimensions: 30″ W x 18″ H x 12″ D

View our Cut List Worksheet and Board Planning Sheet

 

Walls

1×2 Wall Frame (stiles) – 4 @ 18 inches

1×2 Wall Frame (rails) – 4 @ 8 ¼ inches

¼ inch Plywood Wall Panel – 2 @ 11 ¼” W x 18″ H

¼ x 3 Wall Trim (stiles) – 4 @ 18 inches

¼ x 3 Wall Trim (rails) – 4 @ 6 ¼ inches

 

Doors

½ x 2 Door Frame (stiles) – 4 @ 16 3/8 inches

½ x 2 Door Frame (rails) – 4 @ 10 3/8 inches

¼ inch Plywood Door Panels – 2 @ 10 ¼” W x 13 ¼” H

¼ x 3 Door Trim (stiles) – 4 @ 16 3/8 inches

¼ x 3 Door Trim (rails) – 4 @ 8 3/8 inches

 

Inside Walls

2×4 Inside Walls Supports – 4 @ 10 ½ inches

¼ inch Plywood Inside Wall Panels – 2 @ 10 ½” W x 17 ¼” H

 

Miscellaneous

1×2 Crosspieces – 6 @ 27 ½ inches

1×2 Face Frame Legs – 2 @ 18 inches

1×2 Face Frame Top – 1 @ 27 inches

¼ inch Plywood Backing – 1 @ 27 ½” W x 17¼” H

1×2 Stop Block – 1 @ 4 inches

 

Steps

 

1. Prep the Parts

 

Measure your space, and then use our handy Cut List Worksheet and Board Planning Guide to determine the size of your boards. Using a miter saw, cut the parts to size. Drill two pocket holes in each end of the 1×2 crosspieces, the shorter ¼ x 2 frame pieces for the doors, and the shorter 1×2 frame pieces for the side walls using a Kreg Jig, as shown. Be sure to readjust the Kreg Jig between materials. Sand the parts to remove any burs from cutting.
Appliance Garage by Build Basic - Step 1

Blog-Step-by-Step-Line-2002. Assemble the Wall Frames

 

Apply wood glue to the ends of the shorter 1×2 wall frame pieces, and then lay them between the longer pieces. Use a clamp to hold each joint in place before driving 1 ¼ inch Kreg screws though the pilot holes to hold the parts in place. Repeat to create the second frame.
Appliance Garage by Build Basic - Step 2

Blog-Step-by-Step-Line-200

3. Attach the Wall Panels

 

Apply a bead of wood glue to the surface of each frame. Position the wall panel over the frame, covering the Kreg Jig holes. Using a pneumatic nail gun and 5/8 inch finish nails, secure the panel in place. Repeat to assemble the second wall frame and panel.
Appliance Garage by Build Basic - Step 3

Blog-Step-by-Step-Line-200

4. Attach the Wall Trim

 

Apply a bead of glue to the perimeter of the face of each panel, and then lay the ¼ x 3 wall trim pieces in place so that the shorter pieces set between the longer pieces. Adjust the pieces until they’re flush with the edges of each panel. Using a nail gun a 5/8 inch finish nails, nail through the trim pieces and into the perimeter of the panels so that the nails sink through the panel and into the 1×2 frame. Be careful to avoid the locations of the pocket hole screws.
Appliance Garage by Build Basic - Step 4

Blog-Step-by-Step-Line-200

5. Add Crosspieces to the Back

 

Stand the assembled walls upright, trim facing outward. Using 1 ¼ inch Kreg Screws, secure the four crosspieces between the side walls flush with their back edges. For reference, place a crosspieces flush with the top edge of each wall, one flush with the bottom edge of each walls, and the other two 2 ¾ from the top and bottom edges. (Note: Pardon the dark wood. I’m using salvaged boards for this part of the project.)
Appliance Garage by Build Basic - Step 5

 

 

Blog-Step-by-Step-Line-200

6. Add Crosspieces to the Top

 

Attach two additional crosspieces flush with the top edges of the walls; one flush with the front edge, and the other towards the back of the assembly about an inch from the back crosspiece.
Appliance Garage by Build Basic - Step 6

Blog-Step-by-Step-Line-200

7. Secure the Face Frame

 

Apply a bead of wood glue to the front edge of each wall. Position the outside edge of each leg of the face frame flush with the face of the side wall, and then secure it by shooting 1 ¼ inch finish nails through the leg and into the front edge of each wall. Apply wood glue to the front edge of the crosspiece, position the remaining piece of the face frame between the vertical legs, and nail it in place flush with the top edge of the legs. (Note: The photo shows the center piece attached first, but I found it would most likely be easier to attach the legs first.)
Appliance Garage by Build Basic - Step 7

Blog-Step-by-Step-Line-200

8. Assemble the Door Frames

 

The frames of the doors assemble much like the walls, except that the panels set inside the frame to hide the cut edge. To create the door frames, lay the shorter ½ x 2 pieces between the longer pieces and secure using wood glue, clamps and 1 inch Kreg Screws.
Appliance Garage by Build Basic - Step 8

Blog-Step-by-Step-Line-200

9. Position the Door Trim

 

Apply wood glue to the surface of each frame. Place the ¼ x 3 trim pieces on the frame so that the shorter pieces set between the longer pieces and flush with the edges of the frame, as shown.
Appliance Garage by Build Basic - Step 9

Blog-Step-by-Step-Line-200

10. Attach the Door Trim

 

Using a nail gun, shoot 5/8 inch nails through the ¼-inch-thick trim and into the ½-inch-thick frame.
Appliance Garage by Build Basic - Step 10

Blog-Step-by-Step-Line-200

11. Insert the Door Panels

 

Flip the assembled doors trim-side-down on the work surface. Apply a bead of wood glue to the exposed back of the trim pieces. Place the panels face down onto the ledge.
Appliance Garage by Build Basic - Step 11

Blog-Step-by-Step-Line-200

12. Attach the Hinge Support

 

Place the ¼ x 3 inch hinge support block on the back of each door panel. Position the board so that it is tight against the outside edge of each panel. Nail the board in place on each door using a nail gun a 5/8 inch finish nails.
Appliance Garage by Build Basic - Step 12

Blog-Step-by-Step-Line-200

13. Create the Slider Block

 

Mark the slider block 3 ¾ inches from each end. Place the panel side of each hinge flush with the edge of the block and inside the line as shown. Drill pilot holes and attach the hinges using the screws provided.
Appliance Garage by Build Basic - Step 13

Blog-Step-by-Step-Line-200

14. Attach the Hinges to the Door

 

Position each door flush with the bottom edge of its slider block. Using the instructions provided with the hinges, position an even gap between the door and the slider block. Drill pilot holes and attach the hinges to the doors using the provided screws.
Appliance Garage by Build Basic - Step 14

Blog-Step-by-Step-Line-200

15. Attach the L-brackets

 

Flip the doors hinge-side-down. On the face of each slider block, position an L-bracket ¾ inch from each end and flush with the outside edge. Using a drill driver and 5/8 inch wood screws attach each L-bracket. These brackets will slide along the inside edges of the wall frame to keep the door from tipping as it slides.
Appliance Garage by Build Basic - Step 15

Blog-Step-by-Step-Line-200

16. Dryfit the Doors

 

Tip the doors under the face frame and against the side walls. Position the sliders so that the L-brackets sit inside each of the wall’s 1×2 frame pieces. If the L-brackets don’t slide smoothly along the inset of the frame, reposition the brackets as needed. Remove the door until installation in step 19.
Appliance Garage by Build Basic - Step 16

Blog-Step-by-Step-Line-200

17. Build the Inside Walls

 

Position two 2×4 boards flush with the top and bottom edges of the ¼ inch inside wall panel. Using a nail gun and 1 ¼ inch finish nails, attach the panel to the 2x4s. Repeat to create the second inside wall.
Appliance Garage by Build Basic - Step 17

Blog-Step-by-Step-Line-200

18. Dryfit the Inside Walls

 

Tip the inside walls under the face frame and into place. With the panels facing outward, position the 2x4s 1 ¼ inch from each wall. Mark the placement on the crosspieces and remove the inside walls.
Appliance Garage by Build Basic - Step 18

Blog-Step-by-Step-Line-200

19. Secure the Doors and Inside Walls

 

Slide the doors back into place, and then position the inside walls. Using a drill driver and 1 ¼ inch screws (I just used the Kreg Screws from earlier), secure the inside walls by driving screws through the crosspieces and into 2x4s.
Appliance Garage by Build Basic - Step 19

Blog-Step-by-Step-Line-200

20. Attach the Stop Block

 

Mark the center of the stop block and the center of the face frame. Align the centerlines and clamp the block in place behind the face frame. Using a nail gun, secure the block by nailing through the face frame and into the block using 1 ¼ inch finish nails.
Appliance Garage by Build Basic - Step 20

Blog-Step-by-Step-Line-200

 

MORE BUILDING PLANS

 

14 thoughts on “Build a DIY Appliance Garage

  1. Marissa

    Hi! The link to amazon for the sliding hardware seems to no longer work– is there a particular name for this type of hardware that I can search? Thank you so much!

    Reply

  2. Pingback: Clever Uses For That Space Under Kitchen Cabinets

  3. Irene Trentham

    That is indeed a great concept, Jenn. Painting it black with a semi-gloss finish would be great too as it would make the dirt less visible considering it’s the kitchen.

    Definitely bookmarking this for future reference. Thank you for the very detailed guide!

    Reply

Leave us a Comment!